ALUMINUM HEATER HOSES @ Automotive online store

ALUMINUM HEATER HOSES Stronger and more efficient than original paper-type hoses. Choose black or silver. Replace worn or leaky hoses quickly and easily. Help restore heater to peak performance. Flexible hoses bend easily to desired shape. 2"ID hose is 18"L and can be easily trimmed tolength needed.
Manufacturer: Dee Engineering
SKU: 10101-2002931

CLASS D AMPLIFIER Unique "rail" power system lets you switch from high-voltage mode for super power into 4-ohm speakers to high-current mode to drive subwoofers and multi-speaker loads Full power even into 1-ohm loads! MOSFET power supply (discrete MOSFET outputs) Mono…subsonic filter included! 300W x 1 RMS into 4 ohms. 20 Hz-100 Hz @ 0.2% total harmonic distortion. 600W x 1 RMS into 2 ohms. 20 Hz-100 Hz @ 0.6% total harmonic distortion. Variable high-pass/low-pass filter (50-300 Hz). Subwoofer crossover. 40 Hz EQ boost. Gold-plated recessed connectors. Frequency response: 5-50 Hz. impedance: 1-8 ohms (stereo), 2-8 ohms (bridged). Line-level and speaker level input. 1400-Watt maximum power. Approximately 14-1/8" x 2" x 10-1/2".
SKU: 10101-2010391

GOJAK® 5000 VEHICLE-POSITIONING JACK Lifts vehicle without touching frame! Load ratings: 1,250 lbs. per jack, 5,000 lbs. per 4-jack set Lifts tires up to 9" wide Effortless mobility—rolls easily in any direction. 2 jacks permit full 180° vehiclepivot&133;4 jacks place vehicle on 360° rolling platform. Moves totally disabled vehicle in tightest areas. No need for electric power, hydraulic elements or compressed air. Non-marring, easy-roll industrial nylon caster wheels with heavy-duty bearings. Easy foot-pedal lifting. Double-pawl bi-directional ratchet lifts tires between 2 rollers…smoothly raises vehicle in just seconds. Roller touches tire only. Rigid steel frame. Polyester powder-coat finish. Built-in carry handle. Weighs approximately 30 lbs. Four heavy-duty wheels. Limited one-year warranty. Shipped separately from factory. NOTE: SKU numbers ending in F are factory shipped and may take a little longer to reach you.
SKU: 10101-2008306

3" OR 4" DRILL PRESS VISES Cast iron base, hardened steel jaws Chrome-plated cold-rolled steel screw for smooth action Heavy-duty vises bolt to drill press table, workbench…almost anywhere! Slotted base for easiest positioning. Chrome-plated crank handle swivels out of the way when not needed. Bolts not included. 3" Vise. 3"W jaws opento 3". Approx. 5-1/4" x 5-3/4" overall. 4" Vise. 4"W jaws open to 4-1/16". Approx. 7-1/2" x 6-1/2" overall.
Manufacturer: MIT
SKU: 10101-2007943

GEAR PULLER Takes any diameter to 6"Black enamel finish Malleable iron crossbeam, two 3" arms, drop-forged steel jaws. Perfect for timing gears, pump shaft and magneto gears, generator and starter repairs.
SKU: 10101-2004257

ASHTRAY BUMPER WEATHERSTRIPPING OEMquality Easy to install Shipped separately from factory. NOTE: SKU numbers ending in F are factory shipped and may take a little longer to reach you.
Manufacturer: Metro Molded Parts
SKU: 10101-2000264

QUICK/STICK™ SHIFTER KIT Shifter is designed forquicker, more positive shifts plus comfort—curved stick brings shifter closer to driver Reduces shift throw up to 30%! CNC machined from billet aluminum to precise tolerances, then cold forged for strength Billet aluminum housing for added strength and reduced wear. Polished finish—a bonus for any interior. Installs easily using simple hand tools. Accepts factory knobs and most aftermarket custom knobs. Instructions included.
Manufacturer: Mr. Gasket
SKU: 10101-2001177

CHROME-PLATED INSTRUMENT PANEL ACCENT Custom-fit showroom chrome-plated molded ABS plastic instrument panel accent adds a custom highlight to fairing dash Contoured to fit over original charcoal plastic gauge panelfor a factory-installed look Attaches with pressure-sensitive self-adhesive backing (included) Instructions included.
SKU: 10101-2008979

4-PIECE COMPLETE ECONOMY 18OZ CARPET MAT SET FOR VANS Set includes 2-piece front and "T" shaped rear mat with runnerto fit in front of third row Long-wearing, heavyweight, cut-pile 18-oz. poly carpet Nibbed backing keeps mats in place and prevents curling Affordable floor protection! No-ravel cloth-bound edges. Tailored to fit—no cutting or trimming. Shipped separately from factory. NOTE: SKU numbers ending in F are factory shipped and may take a little longer to reach you.
SKU: 10101-2007322

CHROME-PLATED REFLECTOR GRILLE Molded ABS plastic grille mounts with self-adhesive pressure-sensitivebacking Fits side and rear reflectors on GL1800
SKU: 10101-2006644

72-PIECE AIR TOOL SET Set includes 4 top-quality air tools plus needed accessories Invaluable for a wide variety of shop, auto, garage or home maintenance/repair projects 1/2" Drive Air Impact Wrench. Plus eight 1/2" drive sockets (3/8" through 7/8"), 1/2" drive 3" extension bar and 4mm hex wrench. 3/8" Drive Air Ratchet. Plus four 1" Phillips bits (1, #2, #3), four 1" slotted bits (1/8" through 5/16"), two star-shaped bits (T10, T15), 3/8" female to 1/2" male drive adapter, bit holder. 1/4" Drive Air Die Grinder. Plus 2 collets (1/4", 1/8"), ten grinding stones (five 1/8" shank, five 1/4" shank), 2 sanding drums (3/4", 1"), 8 sanding sleeves (four 3/4", four 1"), 1-1/2" steel wire brush with1/4" shank, 2 rotary tool wrenches. Air Hammer. Plus 3 chisels (flat, tapered and tailpipe) and chisel spring. Blow Gun. Plus safety nozzle, rubber tip, tapered hose tip. And More: Quick-connect body, six male quick-connect plugs, two connectors (male/male, female/female); dual tire chuck, mini oiler, Teflon® tape, compartmented storage case.
Manufacturer: Mechanics Products
SKU: 10101-2007627

DIXIE HORN Announce your arrival or departure tunefully with this exciting horn. Five air trumpetsplay the famous first 12 notes of "Dixie" at the touch of a single button. Durable plastic trumpets are graduated in length from 5-1/2" to 10-1/2" and play at a powerful 118dB. Easy to install…no tanks or valves needed. Set includes trumpets, tubing, compressor, relay, mounting hardware and instructions. For all 12-volt vehicles. NOTE: If you are replacing your existing horn, this kit includes all necessary hardware. If you are purchasing as an auxiliary horn, you will also need a horn installation kit, which is sold separately below (item ZX888315).
Manufacturer: Wolo
SKU: 10101-2009059

CHALLENGER CUSTOM STEERING WHEEL World-class styling for your Jeep's interior! Impressive 3-dimensionalhigh-tech dual-plane design at a very affordable price 4 cutout steel spokes Extra-thick foam-cushioned grip covered in textured black vinyl. 13-1/2" diameter with 3" dish. Mounting kit sold separately.
Manufacturer: Grant
SKU: 10101-2003123

HOW TO HOT ROD VOLKSWAGEN ENGINES This detailed manual shows you how to get better acceleration, top speed and improved handling. It also shows you how to set up the engine for general use, drags, sports car racing and more. Covers carburetion, exhaust, camshafts, ignition assembly techniques and more for 1200cc, 1300cc, 1500cc and 1600cc air-cooledengines. Over 160 pages, approx. 400 photos.
SKU: 10101-2006818

CUSTOM-FIT TAILGATE CARPET Custom-fit tailgate carpet designed to complete the look of your interior restoration—without spending a lot! Latex backing and color-coordinated bound edges For best color match, order at same time as carpeting You can't go wrong with these fabrics and textures! Detailed with sewn-in contours for a perfect fit. Exposed edges are protected/strengthened with reinforced binding. Padding insulates against noise and vibration. Screws and instructions included. Shipped separately from factory. NOTE: SKU numbers ending in F are factory shipped and may take a little longer to reach you. To receive a color fabric sample(s), call (800) 603-4383 and request thecolor(s) you would like.
Manufacturer: Auto Carpet Systems
SKU: 10101-2004644

AMG 5-spoke 220 2pcSilver w/Machined Lip Wheels priced from $999.00 to $1099.00. AMG 5-spoke 220 2pc Silver w/Machined Lip Wheels.
Manufacturer: AMG
SKU: AMG 5-spoke 220 2pc Silver w/Machined Lip Wheels
Category: Automotive Parts and Accessories Parts Wheels

The perfect companion to a Bikini top. Covered with soft top material in factory matched colors by Bestop. Each door has a sturdy inside latch and a welded steel frame. Smooth outside look with new low-profilehinges. Super quick installation, no drilling required. These click shut with flush exterior paddle handles. Models for all CJs, Scramblers and '87-00 Wranglers. **'81-'86 CJ7 with steel doors (paddle handle) use YJ soft doors.**
SKU: 21041 15
Category: Miscellaneous

DUNE BUGGY SKID PLATE Attaches to rear bumper Fits all Volkswagen-powered vehicles Protects entire underside of engine fromdamage during off-road driving. 23-1/2"W. Made of 14-gauge steel. Mounts easily to engine case and chassis pan. Includes hardware. Heater boxes may require some modification. Fits all Volkswagen-powered vehicles.
Manufacturer: Dee Engineering
SKU: 10101-2004727

Add comfort and convenience. A large carpeted lockable storage compartment, padded armrest, twin multi-drink holders and factory matched black add up to the best padded console on the market. New heavy duty hinge and lock rail. Hardware, mounting bracketand step-by-step instructions included. Not to be confused with cheap imitations, this is Genuine Bestop quality. Fits only CJ models. Console Measures 24"x9.5"x13"
SKU: 24022 09
Category: Miscellaneous

BIG-BORE PISTON AND CYLINDER KIT The ultimate performance kit from an industry leader! A must for every serious engine builder Complete with strong, extra-thick cylinders, FORGED pistons, rings, pins and clips For standard 1300-1600cc engines. Some machining required.
Manufacturer: Dee Engineering
SKU: 10101-2005222

CAST ALUMINUM VALVE COVERKIT Finned premium-quality cast aluminum with black finish—impressive alternative to chromed steel or plastic Enhances engine compartment Helps eliminate oil leaks and quiets valve train noise. Less chance of warping than with plastic or stamped metal covers. Complete with gasket, grommets, oil filler cap and mounting hardware.
Manufacturer: Omix Ada
SKU: 10101-2005535

"BOY RACER" WING Blow molded ABS Plastic Installs using factory holes Looks great with other 3dCarbon™ "Boy Racer" accessories! Add some attitude to your Mustang! Designed specifically to replace the factory rear wing and can be installed directly into the factory rear wing holes. The spoiler weighs approximately 5.5 lbs. and is pre-primed ready for final sanding andpainting. The height from the deck lid to the top of the rear wing in the front is 6". The height from the deck lid to the top of the rear wing in the rear is 7". Shipped separately from factory. NOTE: SKU numbers ending in F are factory shipped and may take a little longer to reach you.
Manufacturer: 3dCarbon
SKU: 10101-2010437

XENON STROBE LIGHT Add flashing color anywhere inside or outside your vehicle! Light flashes 2-1/2 times per second Attaches easily with 2-sided tape Connects to Strobe Control Module (sold separately; item # ZX270486) to select a flashing pattern. Hardware and instructions included. Only1-5/8"W x1/2"H x 2-3/4"L. Easy 2-wire hookup to vehicle's 12-Volt negative-ground system. Limited lifetime warranty. Note: Check local laws before ordering.
Manufacturer: Street Glow
SKU: 10101-2010480

DUAL-TRUMPET ELECTRIC HORN SET It sounds like a powerful air horn—but it's not! Uses existing horn button and relay Delivers a commanding 118 dB blast without a compressor or airlines Easy installation in minutes on any vehicle with a standard electric horn. Only 2 wires to hook up. Plastic trumpets won't rust.
Manufacturer: Wolo
SKU: 10101-2008996

5" COMPETITON EL® TACH Electroluminescent white face that glows blue when you switch on the power Digital Morphing Control (sold separately) lets you change the face color (from cool blue to neon green) and intensity for a radical look in any setting Made to the highest quality standards for unparalleled precision and accuracy 5" diameter and 2" deep. 10,000-RPM scale with internal and external shift lights. Adjustable Shift/maximum-RPM set points. Rotates within mounting for best viewing. Full metal housing. Works with 2-, 3-, 4-, 5-, 6-, 8- and 10-cylinderengines. Ultra-slim design for easy mounting almost anywhere—all needed fittings and adapters are included. Vibrationproof air-core meter. Brushed aluminum bezel. Easy-to-read black numerals.
SKU: 10101-2008911

RACING SPORT PEDAL PAD WITH HOLES SET Premium-quality aluminum Easy clip-oninstallation to existing pedals—no drilling required Set for automatic transmission includes brake and gas pedal pads. Set for manual transmission includes clutch, brake and gas pedal pads.
SKU: 10101-2003006

The easy-to-install tailgate security system that makes locking & unlocking your pickup's tailgate as convenient as locking & unlocking your doors all without leaving the comfort of the cab. The Pop & Lock power Tailgate Lock "deadbolts" your tailgate, preventing it from being stolen and, with a cap or tonneau, protects the contents in the bed as well. Mounts easily & permanently inside the tailgate and ties quickly into theexisting power door lock system. No drilling required to install.
SKU: 73001 500
Category: Miscellaneous

Manufactured to OEM tolerances by Bestop, this set will help you to keep your interior cooler with 31% tinted rear windows. Three piece tinted window sets will reduce heat build-up. And let's face it - they look cool too!! Versions for all '88-'95 Wranglers with the original top or with a Bestop Replace-a-Top with half steel doors. (won't work with full steel doors or Bestop Supertop and Sunrider)

SOLAR WINDOW SHEILD Inexpensive way to keep your vehicle cool in summer and warm in winter Installs easily with hook/loop tape—no tools required! Removes effortlessly when not needed Protect your interior—keep heat and sunlight out! Shield has a silver surface to reflect sunlight plus double insulation (R-12 factor)to reduce heat loss in colder weather.
Manufacturer: Spectra Products
SKU: 10101-2004525

Isn't it time for a really nice carpet that fits exactly? The Proline molded carpet kits from Nifty feature original equipment style quality. Pressure formed and than trimmed for an exact fit to your vehicle. The mold includes the rear wheel housing sidewalls for the most complete coverage. Available in black, dark charcoal, dark tan, dark sand and gray. This complete kit exists of 6 pieces.
SKU: 14051 433
Category: Miscellaneous

Replace your rusted, bent or cracked originals. Choose from either bright stainless steel or black matte steel. **Fits 82-86 CJ's with 2 bolt Caliper Plates**
SKU: 56217 13
Category: Miscellaneous

PERFORMANCE MASS AIRFLOW SENSORS 10 to 15 horsepower increase at rear wheels! 50-state legal Innovative sensor features a state-of-the-art active-electronic module that provides improved control of both ignition and injector timing, contributing to the big horsepower gain at therear wheels. 47% more airflow capacity than stock sensors. Sensor is housed in a high-impact injection-molded body to reduce heat "soak", a problem common to stock metal sensor. Installation of this sensor will not affect mileage or drivability under normal conditions. Easy to install in minutes. Instructions included.
Manufacturer: Granatelli Motorsports
SKU: 10101-2005582

STROBE ACCENT LIGHT Small enough to mount anywhere you want a unique pulsating light RuggedLexan® construction survives rough travel Features built-in transformer Easily installs anywhere. Plugs into cigarette lighter or permanently wires to 12-volt system (only 2 wires to hook up). Approximately 1-5/8"W x 2-3/4"L x 1-3/8"D. Limited lifetime warranty. Brackets, hardware and instructions included.
Manufacturer: Street Glow
SKU: 10101-2003528

SPORT MAX 2-IN-1 ALUMINUM BI-FOLD RAMPS Two ramps for the price of one! Includes two one-piece 15"W sections—use them as separate ramps or connect them to form a single extra-wide 30" single ramp for bigger loads Durable, rust-resistant, lightweight aluminum Fold for trouble-free transport or storage. 1,250-lb. capacity per section (2,500-lb. capacity total). Includes 2 ramp sections plus self-locking slip hinge to interlock the individual sections and adjustableattachment straps.
SKU: 10101-2004717

ENGINE SWAP MOTOR AND TRANSMISSION MOUNTSEnsure smoother, more positive performance while increasing horsepower Choose from a variety of mounts—one's just right for you! For American vehicles
Manufacturer: Trans Dapt
SKU: 10101-2001023

HEAVY-DUTY RUBBER BED MAT WITH LOGO Priced-right protection for your full-size pickup's bed with a custom flair! You can depend on this workhorse not only to prevent mars, scratches and dents but also to prevent your cargo from sliding around! Licensed logo in the center makes a powerful styling statement Slips easily into place. Simply hose off to clean. Will not fit Stepside models. LB=Long Bed. SB=Short Bed. Chevy Bow Tie® is a trademark of General Motors Corp. Ford Oval logo is a trademark of Ford Motor Company. Dodge Ram Logo is a trademark of Daimler Chrysler Corp.
Manufacturer: Autotecnica
SKU: 10101-2004635

FULL-FLOW OIL FILTER For 1954-1979 air-cooled Volkswagen & reg; engines. Note: Not for automatic transmissions. Mounts to high-volume oil pump (sold separetly; sku # ZX150109B). Traps damaging particles to ensuretrouble-free performance and easy maintenance.
Manufacturer: EMPI
SKU: 10101-2002797

CHROME-PLATED BOW-TIE ENGINE DRESS-UP KIT For '59-86 Chevrolet small-block engines Distinctive bow-tie emblem embossed on the valve covers, breather cap, wing nuts and spark plug looms gives these components their unique appeal All parts are made to GM specifications 20% heavier than aftermarket replacement parts. All, except grommets, are heavily chromed plated and polished to a highluster. Replace originals perfectly. Rubber grommets, dipstick with tube and hold-down clamps included. General Motors trademarks used under license to Specialty Auto Parts USA, Inc. Timing cover and tab sold separately.
Manufacturer: PROFORM
SKU: 10101-2005392

U-GROOVE SPARK PLUGS The best there is! Outperform V-design, split and platinum plugs Made exclusively for high-performance street and racing engines Put more fire "in the hole" for more power to the wheels! Unique U-groove ground electrode minimizes flame dissipation to ensure most complete combustion even with a lean air-fuel mix. U-groove improves "ignitability" and increases fuel combustion for better performance. Nothing to quench flame and cause misfires and rough idle aswith conventional plugs. Firing is dramatically improved without increasing spark gap. Improve throttle response and fuel efficiency. Set of 4 spark plugs—order the number of sets required for your vehicle. MORE REASONS NO OTHER PLUG COMPARES! Copper-glass seal bonds insulator to electrode for a gas-tight seal. Electric heat seal ensures stable heat range for uniform performance. U-groove ground electrode develops a larger spark nucleus for better, faster combustion and reduced fouling. Ribbed insulator provides superior strength, conductivity while preventing arcing. Copper-core center electrode with nickel-chrome shell for superior electrical conductivity and maximum heat dissipation. Machine-rolled threads for trouble-free installation/removal.
Manufacturer: APC
SKU: 10101-2005161

Top quality replacementcomponents bring new life to your tired Wiper System. Check model year when ordering.
SKU: 55307 07
Category: Miscellaneous

REPLACEMENT HINGE PIN FOR VW REAR VIEW MIRRORS For '68-79 Volkswagen Beetles and Super Beetles For '68-79 Beetle and Super Beetle convertibles: restores proper hinge function wheninstalling mirror. Threaded top. Rust-resistance stainless steel. For driver's or passenger's side.
Manufacturer: West Coast Metric
SKU: 10101-2008335

1/2-AMP MOTORCYCLE BATTERY CHARGERS Small 2" x 2-1/2" x 1-1/2" module stores under seat Available with permanently attachable leads or alligator clips, 12-volts or 6-volts Chargers allow recharging or trickle charging without removing battery Plugs into any 110- to 120-voltoutlet. 6-ft. quick connect/disconnect cable included. UL listed.
SKU: 10101-2006111

O.Z. Wheels priced from$149.00 to $1499.00. OZ Wheels from The Tire Rack
SKU: O.Z. Wheels
Category: Automotive Parts and Accessories Parts Wheels

STEEL RUST REPAIR PANELS 22-gauge cold-rolled automotive-quality steel (except where noted) Panels install with screws,rivets or by welding Replace rusted or dented parts and make your vehicle look new again!
SKU: 10101-2000568

BOLT-ON VALVE COVERS Polished, premium-quality cast aluminum with cast-in EMPI logo Finned design reduces upper cylinder head temperatures Enough clearance for most high-lift rocker arms Special channel-type seals and stud seals for apositive seal. Complete with all gaskets and hardware. Sold in pairs.
Manufacturer: EMPI
SKU: 10101-2005520

SPECIAL SOCKET PLUG WEATHERSTRIPPING OEM quality Easy to install Shipped separately from factory. NOTE: SKU numbers ending in F are factory shipped and may takea little longer to reach you.
Manufacturer: Metro Molded Parts
SKU: 10101-2000277

UPPER A-ARM SUSPENSION BUMPER WEATHERSTRIPPING OEM quality Easy to install Shipped separately from factory. NOTE: SKU numbers ending in Fare factory shipped and may take a little longer to reach you.
Manufacturer: Metro Molded Parts
SKU: 10101-2000269

CHROMED SPEEDOMETER AND TACHOMETER COVERS AND HOUSING Chrome-plated metal covers and housing mount on original gaugeswith existing hardware Covers and housing sold separately
SKU: 10101-2008987

FIBERGLASS BAJA REAR DECK LID Bolt-on installation using existing hardware Strongyet lightweight fiberglass lightens your Beetle! High-gloss gelcoat finish—some surface prep required before painting This is a difficult installation that may require trimming. Will NOT fit Super Beetle. Shipped separately from factory. NOTE: SKU numbers ending in F are factory shipped and may take a little longer to reach you.
Manufacturer: EMPI
SKU: 10101-2001914

DELUXE POLY PRO III BREATHABLE 5th WHEEL RV COVER WITH ZIP-UP PANELS Heavy-duty Poly Pro III fabric features triple-layer polypropylene top and polypropylene sides—strong, water resistant and breathable Air vents minimize wind lofting and help prevent moisture buildup, mold and mildew under the cover Full-height zippered panels allow complete access tothe door, side and rear Protects your vehicle from the sun's UV rays, airborne pollutants, snow, rain, ice, etc. Prevents interior sun fade and deterioration. Elasticized corners and adjustable front and rear tension panels ensure a snug, custom-like fit—even around the nose. Unique tie-downs and rope help hold cover in place. Lightweight, easy-to-handle cover slips on easily. Storage bag and rear ladder cap included. Limited 3-year warranty.
SKU: 10101-2004597

REAR SEAT PADDING KITS Helps restore deteriorated seats to like-new looks and comfort Make reupholstery jobs a snap! A must when installing new seat covers! Durable molded foam cushions fit easily over framework of seat and are thencovered with your upholstery. Includes one backrest and one bottom cushion.
Manufacturer: T M I
SKU: 10101-2007067

A new style of headlight covers for modern trucks like yours. These simulate the look of projector beam lightsby being completely clear in the direct path of the beam from your stock headlights, while having the carbon fiber look on the rest of the lens. No drilling required for installation. Limited Lifetime Warranty.
SKU: 71079 100
Category: Miscellaneous

BLACK POWDER-COATEDSPORTSMAN™ GRILLE GUARD Heavy-duty steel with black powder-coated finish for maximum rust protection even in the worst climates Custom-fit tubing contours around front end, grille and headlight area for a superb, customized look Heavy-duty steel uprights with thick rubber extrusions for added protection This grille guard extends approximately as high as grille and as wide as vehicle to completely protect front end—grille, headlights and bumpers! Easy to install without drilling. Modular design simplifies installation and reduces shipping costs. Cross tube features light-mounting provisions (lights not included). Light guards are removable for trouble-free access to headlights. Features include: 1-1/2" grille guard, 1-1/2" hood guard, light guard, welded 1-1/2" cross bar (on many applications). Mounting hardware and installation instructions included. Limited 5-year warranty. Looks awesome with Westin® Black Powder-coated Sportsman™ Taillight Guards (sold separately)!
Manufacturer: Westin
SKU: 10101-2004919

Save when you buy our Bestop bikini, windjammer and duster combo. This kit comes complete with the necessary products to quickly install the kit. Made by Bestop to factory matched colors in genuine (original specs) Haartz material. Thiskit is for when your '80-'86 CJ7 has a Bestop Supertop. Kit does not come with a channel, use your existing Supertop channel.
SKU: 20070 01
Category: Miscellaneous

OR-FAB SPORT CAGE AND ACCESSORIES Tubular steel cage acts as a rugged protectivedevice for the serious off-roader and rock crawler! Patented interior enclosure—the safety feature the factory left off! Bolts easily to your Wrangler's hardtop or soft top…looks clean and factory installed Won't block A/C, heater vents or window cranks. Won't take up any valuable leg room. Tough black powder-coated finish. Some drilling may be required. Accessories sold separately. All necessary hardware included. Questions? Log onto www.performanceaccessories.com.
Manufacturer: Perfornance Accessories
SKU: 10101-2002717

DRAWBARHITCH 3,500-lb. GTW, 300-lb. tongue weight. Available in 4" drop or 6" drop For vehicles with step bumpers Mounts to 3/4" or 1" hitch ball hole on step bumper. Drilling one additional 1/2" hole required. Accepts ball with 3/4" shank. An easy and affordable way to lower and extend hitch ball away from bumper. Powder-coated steel. With mounting hardware. Note: Do not exceed rated towing capacity of bumper or towing vehicle.
Manufacturer: Acar
SKU: 10101-2004368

STORMSHIELD™ CAR COVER Custom-designed to cover your PT Cruiser in style! Storm rated for top all-weather protection Fights "aging" and protects expensive paint jobs from dust, sun, water spots, bird droppings, tree sap, acid rain and most other natural and man-made "hazards" One of the best car cover fabrics available, especially for cars subjected to snowy or icy conditions! Special PT Cruiser flame design available Keeps interior cooler and stored valuables out of sight. 3-layer fabric is made of woven polyester material to lock out the great outdoors and to block the sun's UV rays. The inner layer is sprayed and then embedded with microscopic cotton fibers to produce a "peach fuzz" finish soft enough to pamper the most delicate paint surface. Fabric "breathes" to prevent damaging moisture buildup. Features overlapped, double-stitched seams, elasticized front and rear hems for a snug fit and reinforced grommets for secure tie-downpoints. Lightweight, easy to handle and store. Lock and storage bag sold separately. NOTE: SKU numbers ending in F are factory shipped and may take a little longer to reach you.
Manufacturer: Coverking
SKU: 10101-2004547

TRAILER BRAKE ASSEMBLIES New…not rebuilt—restore safe, dependable braking action! Ideal for salt water environments Assemblies include backing plate, shoes, wheel cylinder and shoe mounting hardware. Galvanized units are hot-dipped in zinc/iron corrosion inhibitor, making them rust and abrasion resistant. Easy to install: simply disconnect brake line and4 bolts on backing plate.
SKU: 10101-2004431

This is the most economical way to replace old & worn out upper doors and fabric. Complete upper doorassemblies come with steel frame and matching soft top fabric skin. Replacement door skin sets attach to existing door frames with durable hook and loop fasteners. Imported
SKU: 11042 317
Category: Miscellaneous

Put one of these stylish units in that empty receiver hole on your hitch. The Jeep® logo looks great & provides the ideal finishing touch. An optional lock (72019.44) secures the plug in its place to foil thieves. Fits Class III receiver hitches only. Choose Black or Silver.
SKU: 12019 12
Category: Miscellaneous

Michelin Symmetry Tire priced from $70.00 to $121.00. The Symmetry radial is a premium All-Season tire that is comfort tuned for luxury cars, family cars and minivans. As its name implies, the Symmetry radial was developedto provide balanced proportions of ride quality, noise comfort and overall performance, as well as year round traction, even in light snow.On the outside, the Symmetry radial features a symmetric tread design with wide, serrated circumferential tread grooves to evacuate water and slush out from under the tire’s footprint to enhance foul weather traction and resist hydroplaning. The tread’s interlocking “S” shaped sipes provide snow biting edges and are combined with a weather-tuned tread compound to provide traction on dry, wet and light snow-covered roads. Internally, the Symmetry radial features twin steel belts that stabilize the tread area to provide strength and enhance treadwear, and a polyester cord body to provide a smooth ride.The Michelin ...
Manufacturer: Michelin
SKU: Michelin Symmetry Tire
Category: Automotive Parts and Accessories Parts Tires

144" LONG STRAP TIE-DOWN WITH RATCHET AND 2 SOFT HOOKS Long-wearing heavy-duty weather-resistant 1"W nylon web strap (3,800-lb. tensile strength) 2 steel hooks…one is vinyl coated to prevent scratches, the other is zinc plated to resist rust 333-lb. recommended working-load capacity, 1,000-lb. maximum capacity Transporting your cycle or ATV? Hauling heavy loads? Secure it and stop worrying about costly damage! Ratchet allows easy tightening and quick adjustments. Extra-long 12-ft. strap can be wrapped around gear for added security. Approximately 18"L integrated cinch straps have soft-hook loop end sewn onto each end for tie-down versatility. Two 3/8" diameter steel"S" hooks. Not designed for lifting or hanging gear.
Manufacturer: R C First Enterpries Inc
SKU: 10101-2004414

Taillight covers look awesome. Available ina smooth or slotted design. Check local vehicle laws concerning use. NOTE: Smooth covers obscure brake lights, for off-road use only.
SKU: 61067 12
Category: Miscellaneous

CLUTCH ALIGNMENT SET Professional-quality tool set made of heavy-duty construction for years of service Complete with storage case, instruction sheets and photos Properly aligns clutch plate and disc to pilot bearing when installing a new clutch Set includes tapered-cone clutch plate adapter, centeringshaft and eight 2-sided adapters (metric and SAE sizes).
SKU: 10101-2004151

REPLACEMENT DUAL CHROMED TRUMPETS Two gleaming chrome-plated die-cast trumpets (13-3/8"L and 10-7/8"L with 3-3/4" diameter bells) are mounted side by side 15-3/4" overall Check local noise abatement laws to avoid legal violations. Sold inpairs.
Manufacturer: Hadley
SKU: 10101-2009006